My litter robot will not cycle

View the Litter-Robot 3 Waste Drawer Liner Installation Video. To change the drawer liner in Litter-Robot 4, pull out the drawer and dispose of the soiled liner. Open a new waste drawer liner and wrap the edges over the rim of the waste drawer. Push the remainder of the bag into the bottom of the waste drawer. Check out the Litter-Robot 4 Waste ...

Once they’ve gotten more accustomed to the Litter-Robot 3, power it on to cycle the unit. While this is happening, make sure your cats are there to watch the motion and to become familiarized with the sound the unit makes. ... So, while my Litter Robot 3 is now clean, it will not have the key. Possibly this should’ve been made clearer ...Considering we've received a huge response on our Litter-Robot II Basic Troubleshooting Guide, we've decided to help our customers further by creating this advanced troubleshooting guide. This guide will help you with opening up the Litter-Robot II to verifying connections of the motor and circuit board.If the Litter-Robot globe jams, the motor will stop and reverse for a few seconds. The unit will then try to cycle again three times. If it cannot cycle after three attempts, the globe will return to the home position, and the control panel will flash yellow and red or blue and red lights.Mechanical Malfunctions. Failure to cycle: One of the most common issues reported with the Litter Robot is its failure to cycle properly. This can result in waste accumulation and an unpleasant odor. Possible causes for this issue include sensor malfunctions or blockages within the device's mechanism. Press the Cycle button to resume the cycle. Press the Reset button to abort the cycle and return the globe to the Home position. 3. After the litter is emptied, the globe pauses with the yellow light bar on and awaits your action. You may need to sweep any remaining litter toward the waste port. 4.

Clean the bezel. If your cat's weight is reading 0.0, clean the bezel. Debris (dust, cat fur, etc) can interfere with the laser sensors and inaccurately measure your cat's weight. Wipe the bezel area where the sensors are located with a dry clean cloth to remove any hair or dust. Vacuum the inside perimeter of the bezel with a brush attachment ...In this video we'll be taking a look at 5 different errors the Litter-Robot 4 may run into and how to fix them. This include LED status identification of the...A user asks for help with a problem of Litter Robot 3 not cycling automatically after cat visits. A support agent provides troubleshooting steps and tips to fix the blue light blinking issue. The user reports that the problem persists and asks for more help.At one point during the first week with the Litter-Robot 4, Ernie entered the litter box mid-cleaning cycle and started peeing. Fortunately, the globe sensed this and stopped rotating.Step 1: Check the Power. The first thing to do when it comes to troubleshooting a Litter Robot that is stuck mid-cycle is to check the power. Make sure the unit is plugged in and the power cord is securely connected to the unit and the outlet. If the power cord is loose, securely reconnect it. If the outlet is not functioning, try plugging the ... The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. You will also receive a notification on ... Community for all things Litter-Robot. Post your experiences, tips, tricks, and hacks. ... Will not cycle or empty. Can’t reset Litter-Robot 3 Connect Locked post. New comments cannot be posted. Share Sort by: Best ... My robot works again. I don't know if this will solve your problem but it worked for me.

Litter-Robot 3: Cycle delay setting. The cycle delay is the elapsed time starting from when your cat exits the globe until the unit starts a clean cycle. It can be set for 3, 7, or 15 minutes. The default cycle delay is 7 minutes. Reduce the cycle delay if it is important to minimize odor and/or the time that waste is accessible to other pets ...Unit not cycling after use. Litter-Robot 3. I happened to be in the room where my LR3 is located. I took a peek inside, and noticed a clump in the middle of the litter, but the unit only had a steady blue light. I checked the app but it didn’t indicate the unit was waiting to cycle, as if it hadn’t even detected a cat had been in the globe.1. When your cat exits Litter-Robot, a timer counts down, allowing the litter to clump before a clean cycle begins. 2. During the clean cycle, the globe slowly rotates. The patented sifting process separates the clumps from the clean litter. 3. The clumps are deposited into a sealed waste drawer below. 4.Preparation. Litter-Robot 4 continuously monitors the motor current to ensure the globe is rotating smoothly and is not obstructed. If your unit has a red light bar with partial yellow flashing, this indicates that the globe is most likely jammed or overloaded. The unit will retract and try to continue cycling.The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If the cat sensor has been continuously activated for 30 minutes or more, either by a cat that won’t leave the globe or by too much weight in the unit, the timing light will flash red. You will also receive a notification on your phone if you ...RomanDoesIt. You most likely changed the location of it and placed it on surface where the weight sensor doesn't touch the floor. That way it has no way to know that cat was inside. Therefore, since your manual cycle works, then it's the sensor placement.

Obituaries cresco iowa.

the DFI, the Cat Sensor(s) are deactivated and the unit will no longer cycle automatically. Check or empty the Waste Drawer, then press Reset to cancel the ...Yes. Litter-Robot 4 uses laser and weight sensor technology to detect when your cat enters and exits the globe, which triggers the countdown timer and cleaning cycle. The SmartScale™ will not recognize kittens that weigh less than 3 lbs. Therefore, kittens that weigh less than 3 lbs can use Litter-Robot 4, but not in automatic mode.Litter-Robot 3 Connect. $549. Buy in monthly payments with Affirm on orders over $50. Learn more. Never scoop again and experience a new level of cleanliness with Litter-Robot 3 Connect, the top-rated self-cleaning litter box for cats. Since 2000, over 1 million happy pet parents have upgraded to Litter-Robot.Yes. Litter-Robot 4 uses laser and weight sensor technology to detect when your cat enters and exits the globe, which triggers the countdown timer and cleaning cycle. The SmartScale™ will not recognize kittens that weigh less than 3 lbs. Therefore, kittens that weigh less than 3 lbs can use Litter-Robot 4, but not in automatic mode.I went to the litter robot Support and filled the steps. By doing a hard reset (unplugging the back of the unit for ten seconds) it was resolved. 1. Reply. Share. Ever since I changed the last bag, my litter robot 3 has had its blue light blinking after every use. I can hit reset and it stops, until the next….Litter-Robot must not be touching any walls for the cat sensor to detect your cat and cycle properly. 2. Add litter as needed. Each time you empty the waste drawer, check the globe and add cat litter as needed. Add just enough litter to meet the raised fill line on the black rubber liner, but be careful not to overfill the globe.

Turn off the Litter-Robot and unplug it from the power source. Remove the waste drawer and the bonnet. Locate the sensor calibration button, which is located on the control panel near the power button. Press and hold the sensor calibration button, and at the same time, plug the Litter-Robot back into the power source.Do a Hard Reset. 3. Take a Closer Look at the Bonnet, Globe, and Base. 4. Check the Lights. 5. Recalibrate Your Sensors. 6. Contact Your Litter-Robot’s …Cycling. If you want to reset the cat sensor, you have to press reset when the unit is at the home position. If you successfully reset the sensor, you should see a blue light flash when you press the reset button. If you do not see the green light when you press the reset button, you may need to press and hold the button for a few seconds ...Still I get ‘cycle interrupted’ / solid red light 2-3x times after each time cat goes to the potty (thankfully the unit recovers after set amount of time (like 30 seconds or whatever). ... I clean my litter robot every week. Also hoovering up any debris from in the device and around the sensors. Switched to a dust free litter and q tips.Drawer Full issue. Just got out LR3 Connect a few weeks ago. So far, we love it with the exception of it notifying us that the drawer is full after 1 or two cycles. If we are home it isn’t a huge deal to reset everything but if we aren’t home it won’t cycle after 2 rounds of notifications. The drawer clearly isn’t “full”.Get started by following the steps below. If possible, place Litter-Robot in the same location as the old litter box (at least during transition). Make sure the unit is on a firm, level surface in a cool, dry location. Locate the unit near a power outlet. Ensure the unit isn’t pushed against a wall or into a corner (must not be touching any ...Sep 14, 2023 ... The Litter-Robot is equipped with Anti-Pinch Sensors on both sides of ... After your Litter-Robot cycles ... If your unit is not displaying a solid ...The unit will cycle again 15 seconds after your cat has left the globe or 5 seconds after the bonnet is replaced. If your Litter-Robot is not detecting your cat or not cycling, complete the troubleshooting steps in our Litter-Robot 3: Cat not detected guide. If your Litter-Robot is slowly flashing yellow or stuck upside down due to the cat ... The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. You will also receive a notification on ... If your litter robot 3 is not able to complete a cycle and is flashing yellow randomly, then watch this video for the fix!Our litter robot was giving us nigh...

Don’t clean that one for 2 week intervals (it may smell a bit, so I’d stick with hooded with carbon filter for this litter box) so they’re less encouraged to go in there than the LR. Leave the litter robot off for now, scoop to clean, or cycle it manually. If any improvement, remove the extra litterbox, still manually/scoop LR.

I have a litter robot 3 bought last year. It is now getting stuck in a cycle and is unusable. Symptoms are: A rotation cycle starts and dumps waste Then just before reversing direction the robot stops, the yellow light starts flashing and the globe moves a small amount further in the orginal rotation direction and stops A power off and restart …Preparation. Litter-Robot 4 is equipped with OmniSense™ detection that utilizes laser and weight sensor technology to provide real-time litter and waste drawer levels. OmniSense™ also supports the SafeCat system which continuously analyzes four safety zones to ensure your cat is always safe. There are three sensors located in the top of the ...Get started by following the steps below. If possible, place Litter-Robot in the same location as the old litter box (at least during transition). Make sure the unit is on a firm, level surface in a cool, dry location. Locate the unit near a power outlet. Ensure the unit isn’t pushed against a wall or into a corner (must not be touching any ...Litter-Robot 3: Blue light flashing (Drawer full) Litter-Robot 3 is equipped with infrared emitters and sensors, called DFI sensors, located above the waste drawer that check if the drawer is full each time the globe returns to the Home position. Once a full waste drawer is detected, the unit will indicate it is full with a blue flashing light.Press the Cycle button to resume the cycle. Press the Reset button to abort the cycle and return the globe to the Home position. 3. After the litter is emptied, the globe pauses with the yellow light bar on and awaits your action. You may need to sweep any remaining litter toward the waste port. 4.Nov 7, 2017 ... The cleaning and maintaining of our litter box is the bane of my existence! And lets not talk about the mess that these cute little cats kick up ...Nov 9, 2012 ... The other common reason that people will find the base unit for the Litter Robot is stopping randomly is that the spring in the foot switch at ...If the light bar on your Litter-Robot 4 has a single yellow light that moves with the rotation of the globe, this means your unit is performing a cleaning cycle or an empty cycle. No action is needed. This is a normal light bar status. Please allow the unit to continue the cycle. If you need to pause the cycle, press the Cycle button.

Dte appliance protection plan coverage.

Kel tec cmr 30 upgrades.

Clean the bezel. If your cat's weight is reading 0.0, clean the bezel. Debris (dust, cat fur, etc) can interfere with the laser sensors and inaccurately measure your cat's weight. Wipe the bezel area where the sensors are located with a dry clean cloth to remove any hair or dust. Vacuum the inside perimeter of the bezel with a brush attachment ...As mentioned in the title, my litter robot 3 is stopping mid-cycle when my room light is turned off. I've owned it for a long time and I don't have access to any parts replacement because when I ordered it internationally, it was before Covid, now the company itself I ordered from has closed.. The video will show more of what I meant..Yes. Litter-Robot 4 uses laser and weight sensor technology to detect when your cat enters and exits the globe, which triggers the countdown timer and cleaning cycle. The SmartScale™ will not recognize kittens that weigh less than 1.36 kg. Therefore, kittens that weigh less than 1.36 kg can use Litter-Robot 4, but not in automatic mode.Issues with Litter Robot 4 immediately. My partner and I have had the litter robot 3 without connect for about 3 years and haven’t had any major issues with it. We love it and only wanted to upgrade for the app connectivity, so we decided on the newest model. We set it up where we had the LR3 before, on tile floors, put litter in it and went ...If your Litter-Robot is not detecting your cat or not cycling, complete the troubleshooting steps in our Litter-Robot 3: Cat not detected guide. If your Litter-Robot is slowly …This should reset the Litter Robot and allow it to cycle properly. Exploring the Causes of a Non-Cycling Litter Robot. If the above steps don’t resolve the issue, there may be other underlying causes that need to be addressed. Here are some of the most common causes of a non-cycling Litter Robot: Malfunctioning SensorsMy litter robot keeps turning in the wrong direction for a clean cycle. After I perform a hard reset multiple times, it will occasionally do a normal cycle and return home with a normal solid blue light and it will function normally for a short while but it will once again start to turn the wrong way for about 30 degrees and return back to the normal position with a solid blue light. Any ... Litter-Robot 4: Light codes guide. Litter-Robot 4 control panel features 5 buttons and an LED display for easy operation. Blue flashing. If your unit’s light bar is flashing blue, this indicates that the waste drawer is full. Empty the waste drawer, press the Reset button, then press the Cycle button. Learn more. In today’s fast-paced world, businesses are constantly seeking ways to streamline their operations and improve efficiency. One technology that has gained significant attention is r...Jul 22, 2020 · Litter-Robot 3 blue and yellow lights on. If both the blue and yellow lights are illuminated on your Litter-Robot 3, it means that the unit is in 8-hour sleep mode. (The unit will not cycle automatically during those 8 hours.) If you’d like to deactivate sleep mode, press and hold the Cycle button for 5 seconds. Power the unit off. Unplug the power supply from the back of the base. Wait 1 minute. Press the Power button to turn the unit on. When your unit is powered back on, it will perform a clean cycle. Once the clean cycle is complete, the unit should go back to blue ready status. Attempt to initiate onboarding again by pressing the Cycle and Empty ...Litter Robot 4 stops mid-cycle and won't restart. I have a 4 and am having a consistent issue with the cycle stopping mid-way but not finishing. About 3x a week, I will come into the room and the robot will be stopped mid-cycle, at the point where the hole is lined up with the tray, and a solid red light. My first thought is that, of course ... ….

Lol my robot is arriving next week and I’m reading up on everyone’s experiences so I know what to expect. I suspect my younger of 2 cats will be very curious. I just introduced clay litter to them a couple days ago …Litter robot 4 not wanting to complete cycle. Worked on my litter robot 4 the other day cause it was doing a thing where the colors 3 yellow 2 red would flash in the middle of a cycle. It would try again to cycle about 3 times then would stay stuck in that position. I looked up what those colors meant and it was giving a overload/jammed issue.I clean my litter robot every week. Also hoovering up any debris from in the device and around the sensors. Switched to a dust free litter and q tips. Glad I am not the only one, but sad to see that there might not be a solution to the issue yet. I am afraid of going on holiday in 2 weeks 😱.Step 3: Check the Power Cord. If the waste drawer is not full and the sensors are clean, the next step is to check the power cord. A frayed or damaged power cord can cause the Litter Robot to malfunction and the yellow light to flash rapidly. Make sure the power cord is securely plugged into the unit and the outlet, and check for any …Now, let's run a test cycle. Short press the Reset button, then short press the Cycle button to run a clean cycle. Successful: After your Litter-Robot cycles, it should return to the Home position, displaying a solid blue light. If your waste drawer gauge is accurate (within 5%), you've been successful. Unsuccessful: If your waste drawer gauge ...Most of the impact robots have on society is positive, as they help improve human health and improve the efficiency of industrial and manufacturing processes. They also create jobs...Jan 24, 2023 · litter robot4: litter robot control software: Factory reset, tested with other cats, tried to manually cycle from the controls will works, lifted the globe to see if there is litter in the working mechanisim, tested with less than recommended litter level: Automatic cycles troubles from day 1 of operation: Thank you so much in advance for your ... Litter-Robot 3: Cycle delay setting. The cycle delay is the elapsed time starting from when your cat exits the globe until the unit starts a clean cycle. It can be set for 3, 7, or 15 minutes. The default cycle delay is 7 minutes. Reduce the cycle delay if it is important to minimize odor and/or the time that waste is accessible to other pets ...Nov 7, 2017 ... The cleaning and maintaining of our litter box is the bane of my existence! And lets not talk about the mess that these cute little cats kick up ... My litter robot will not cycle, If YES, you are done. Re-position Globe and verify that it completes a clean cycle (in this case adjustment of the cat sensor was not needed). 5. Turn the Base upside down so you are facing the bottom surface. Find the round black adjustment foot and simply turn it Clockwise (2) full complete turns (720 degrees). 6., Flashing orange, tried everything - help! We can’t get the machine to work. Was cycling and started to flash orange stopped. Pressed reset and emptied the tray. Same problem. Tried turning on and off, reconnecting via the app etc Same problem. Won’t let me reset it. Cleaned whole thing, checked internals -everything seems fine and clean., Now, let's run a test cycle. Short press the Reset button, then short press the Cycle button to run a clean cycle. Successful: After your Litter-Robot cycles, it should return to the Home position, displaying a solid blue light. If your waste drawer gauge is accurate (within 5%), you've been successful. Unsuccessful: If your waste drawer gauge ..., the DFI, the Cat Sensor(s) are deactivated and the unit will no longer cycle automatically. Check or empty the Waste Drawer, then press Reset to cancel the ..., Power the unit off. Unplug the power supply from the back of the base. Wait 1 minute. Press the Power button to turn the unit on. When your unit is powered back on, it will perform a clean cycle. Once the clean cycle is complete, the unit should go back to blue ready status. Attempt to initiate onboarding again by pressing the Cycle and Empty ..., LR4 emptying during clean cycle. Litter-Robot 4. I have my litter robot 4 for 3 weeks now and sometimes during a clean cycle it will empty itself completly. I never saw it happen so I can't say what is happening exactly but in the app it is logged as a "clean cycle completed". It mostly happen after changing the litter bag or adding more litter., Cycling (In use) Working normally; Without rotation DFI sensor or Motor defective; Normal use; Replacement Guide (H) Replacement Guide (K) YELLOW FLASHING (slow or fast) Cycle interrupted. Cat interrupted the cycle; Anti-pinch pins rusted / used; Bonnet terminal pins rusted / used; Base contact pins rusted / used; Wait 15s (if cat interrupted ..., Submit support request. Select a category for your ticket. Select a sub-category for your ticket. Please describe your issue. Got questions or issues? Contact Litter-Robot Support today. We’re dedicated to ensuring a seamless experience for you & your pet., The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. You will also receive a notification on ..., Yes. Litter-Robot 4 uses laser and weight sensor technology to detect when your cat enters and exits the globe, which triggers the countdown timer and cleaning cycle. The SmartScale® will not recognize kittens that weigh less than 3 lbs. Therefore, kittens that weigh less than 3 lbs can use Litter-Robot 4, but not in automatic mode. , Details. Say goodbye to scooping and give your cats clean litter every time they go with Litter-Robot 3, the highest-rated automatic litter box. Purchase includes a 90-day in-home trial, comprehensive coverage with our WhiskerCare™ 1-Year Warranty, and free shipping (excl. AK, HI, PR). Never scoop again®. Helps reduce litter box odors., According to the Brookings Institution, 10 states in the Midwest and South have about half the industrial robots in use. Michigan has the most of the bunch. By clicking "TRY IT", I..., litter robot4: litter robot control software: Factory reset, tested with other cats, tried to manually cycle from the controls will works, lifted the globe to see if there is litter in the working mechanisim, tested with less than recommended litter level: Automatic cycles troubles from day 1 of operation: Thank you so much in advance for your ..., If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the cat sensor or bonnet removal. Press the Reset button to resume the cycle. If your unit returned home and displays a solid blue light, you've been successful. If your unit is not displaying a solid blue light after ... , Robots and artificial intelligence (AI) are getting faster and smarter than ever before. Even better, they make everyday life easier for humans. Machines have already taken over ma..., If the light bar on your Litter-Robot 4 has a single yellow light that moves with the rotation of the globe, this means your unit is performing a cleaning cycle or an empty cycle. No action is needed. This is a normal light bar status. Please allow the unit to continue the cycle. If you need to pause the cycle, press the Cycle button., Preparation. Litter-Robot 4 continuously monitors the motor current to ensure the globe is rotating smoothly and is not obstructed. If your unit has a red light bar with partial yellow flashing, this indicates that the globe is most likely jammed or overloaded. The unit will retract and try to continue cycling., No scooping, literally ever. Because we have three cats, my partner and I would split emptying our litter box once a day. Even with his help, it was a lot and a chore that I admittedly skipped at times due to how much I hated doing it. Since we unboxed the Litter-Robot 4 two months ago, however, it’s automated that process for us, so I ..., Cycling (In use) Working normally; Without rotation DFI sensor or Motor defective; Normal use; Replacement Guide (H) Replacement Guide (K) YELLOW …, Ok so on the side of the bonnet there are 2 tabs make sure they are clicked in. Maybe try taking it off and then placing it back on. You should be able to press the in with your fingers. Shouldn’t need any tools. I have never heard of a “keyhole plug”., Litter-Robot 3: Reset button. The Reset button will reset your Litter-Robot's cat sensor. You can think of the cat sensor as the scale and the Reset button as a way to zero the scale. IMPORTANT: Any time you do anything that affects the weight or placement of the unit, including adding or removing litter, emptying the waste drawer, or moving or ..., Community for all things Litter-Robot. Post your experiences, tips, tricks, and hacks. Members Online • ... Hold the cycle button to disable. Can be found on page 25 of user manual Reply reply Throwitawayeheh2029 ..., Preparation. Litter-Robot 4 is equipped with OmniSense™ detection that utilizes laser and weight sensor technology to provide real-time litter and waste drawer levels. OmniSense™ also supports the SafeCat system which continuously analyzes four safety zones to ensure your cat is always safe. There are three curtain sensors located in the ..., Community for all things Litter-Robot. Post your experiences, tips, tricks, and hacks. Members Online • SirRawrz . Litter robot Unresponsive Solid Yellow light Tips & Tricks I've been dealing with a messed-up robot since last week, it kept cycling, trying to overcycle, and not cycling at all. I've cleaned the entire unit of debris, taken off ..., Considering we've received a huge response on our Litter-Robot II Basic Troubleshooting Guide, we've decided to help our customers further by creating this advanced troubleshooting guide. This guide will help you with opening up the Litter-Robot II to verifying connections of the motor and circuit board., Want to keep your Litter-Robot 3 running perfectly, and avoid those nasty flashing error lights? Performing simple monthly maintenance is key. Litter dust c..., Re-connecting Litter-Robot 3. Perform a hard reset on your Litter-Robot. Unplug the unit from the back of the base. Wait 1 minute. Plug it back in and allow it to cycle. If the unit is still Offline in the app, proceed to the next step. Ensure you are using the latest version of the Whisker app., clean the lenses at the top. reassemble making sure globe is seated. close bonnet, make sure there isn't gaps like in your video. Plug-in, Power on, and see if it rotates now. if not, Try pulling the waste drawer out. unplug, waiting 30 seconds, and plug back in (with the drawer still out). Finally, try a hard reset hold two buttons at once ..., Now, let's run a test cycle. Short press the Reset button, then short press the Cycle button to run a clean cycle. Successful: After your Litter-Robot cycles, it should return to the Home position, displaying a solid blue light. If your waste drawer gauge is accurate (within 5%), you've been successful. Unsuccessful: If your waste drawer gauge ..., Oct 29, 2021 · Please follow the steps below. Open your app. Go to “Remote” and click “Delete my Litter-Robot.”. Completely close the Litter-Robot app. Reset your Litter-Robot by unplugging it from the base while the unit is powered on. Wait 15 seconds, plug it back in, and allow it to cycle until the blue “Ready” status lights up. , Recently my Litter Robot II stopped cycling mid-cycle. Three lights blinking once per second or just the middle yellow light is on. The gear does not move at all. Do not see any obstructions and all connections seem sound. I’m pretty sure it’s a motor issue but wanted to double-check if there was any other trouble-shooting I can check in ..., If your litter robot 3 is not able to complete a cycle and is flashing yellow randomly, then watch this video for the fix!Our litter robot was giving us nigh..., Jan 24, 2023 · litter robot4: litter robot control software: Factory reset, tested with other cats, tried to manually cycle from the controls will works, lifted the globe to see if there is litter in the working mechanisim, tested with less than recommended litter level: Automatic cycles troubles from day 1 of operation: Thank you so much in advance for your ...